Product ID:WATER GUARD-MULTI-SURF WB, 51775A (030591Y)
MSDS Date:04/01/1993
FSC:8010
NIIN:00N065458
MSDS Number: CBCYT

PPG INDUSTRIES INC

4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 304-843-1300

Info Phone: 412-492-5555

Cage: DO542

PPG INDUSTRIES INC. COATINGS & RESINS GP

9 ALLISON PARK, PA 15101

Telephone: 412-492-5555

Cage: DO542

WATER; (DEIONIZED WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 85-90%

OSHA PEL N/K

ACGIH TLV: N/K

FILM,FORMERS, RESINS, & ADDITIVES

Fraction By Weight: 10-15%

OSHA PEL N/K

ACGIH TLV: N/K

LEL IN INGREDIENTS BELOW THE STATED LIMIT, AND TO

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGEST/INHAL:NONE KNOWN. EYE:CAUSES
IRRITATION. SKIN:MAY CAUSE SLIGHT IRRITATION. CHRONIC:AVOID LONG
TERM AND REPEATED CONTACT. THIS PRODUCT EITHER CONTAINS
FORMALDEHYDE OR IS CAPABLE OF RELEASING FOR MALDEHYDE ABOVE 0.5 PPM
UNDER CERTAIN CONDITIONS. FORMALDEHYDE IS POTNTL CANCER HAZ, SKIN &
RESP SENSITIZER.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.

First Aid:INGEST:CALL MD IMMED . IF INGEST, ANY TYPE OF OVEREXP/SYMPS
OF OVEREXP OCCUR DURING/FOLLOWING USE OF PROD, CONT POIS CTL CTR,
EMER ROOM/MD IMMED, HAVE MSDS INFO AVAIL. EYE:FLUSH IMMED W/PLENTY
O F WATER FOR @ LST 15 MIN. SKIN:FLUSH IMMED W/PLENTY OF WATER
FOLLOWED BY WASHING WITH SOAP & WATER. INHALATION:REMOVE TO FRESH
AIR. SUPPORT BRTHG (GIVE O*2/ARTF RESP) .

Flash Point Method:PMCC
Extinguishing Media:USE NATL FIRE PROT ASSOC (NFPA) CLASS B EXTINGS
(CARBON DIOXIDE, DRY CHEM/UNIVERSAL AQUEOUS FILM FORMING FOAM)(SUP
DAT)
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER SPRAY MAY BE INEFTIVE. WATER SPRAY MAY BE USED TO COOL CLSD
CNTNRS TO PVNT PRESS BUILD-UP & (SUPDAT)
Unusual Fire/Explosion Hazard:KEEP CNTNR TIGHTLY CLSD. ISOLATE FROM
HEAT, ELEC EQUIPMENT, SPKS & OPEN FLAMES. CLSD CNTNRS MAY EXPLODE
WHEN EXPOSED TO EXTREME HEAT. DO NOT APPLY ON (SUP DAT)

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERS EQUIPPED W/PROPER
RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN AREA. REMOVE ALL
SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAWDUST, VERMICULITE/OTHER
ABSORB MATL & PLACE INT O CNTNRS FOR DISP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE > 120F. STORE LG QTYS IN
BLDGS DESIGNED & PROT FOR STOR OF NFPA CLASS IIIB COMBUST LIQS.
Other Precautions:IF MATL IS PART OF MULTIPLE COMPONENT SYS, READ
MSDS(S) FOR OTHER COMPONENT/COMPONENTS BEFORE BLENDING AS RESULTING
MIX MAY HAVE HAZS OF ALL ITS PARTS. CNTNRS SHOULD BE GROUNDED WHEN
POURING. AVOID FR EE FALL OF LIQ IN EXCESS OF FEW INCHES.

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN . NONE REQUIRED.
Ventilation:PROVIDE GEN DILUTION/LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONCS OF INGS BELOW LOWEST SUGGESTED EXPOS LIMS, (ING 3)
Protective Gloves:NITRILE OR NEOPRENE RUBBER.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:ANSI APPROVED EMERGENCY EYE WASH AND DELUGE
SHOWER .
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Supplemental Safety and Health
EXTING MEDIA:DESIGNED TO EXTING NFPA CLASS IIIB COMBUST LIQ FIRES. FIRE
FIGHT PROC:POSS AUTO IGNIT/EXPLO WHEN EXPOSED TO EXTREME HEAT. IF
WATER IS USED, FOG NOZZS ARE PREF. EXPLO HAZS:HOT SURFS. TOX B ASES
MAY FORM WHERE PROD IS CONT BY FLAME/HOT SURFS.

Boiling Pt:B.P. Text:>210F,>99C
Vapor Pres:17.4
Vapor Density:HVR/AIR
Spec Gravity:1.01
Evaporation Rate & Reference:35 (BUACT=100)
Solubility in Water:93.5%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
SOLVENTS IN INGREDIENTS.
Percent Volatiles by Volume:87.20

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRDCE HAZ DECOMP PRODS WHEN
HEATED. WELDING, BRAZING/FLAKE-CUTTING MAY PRDCE FUMES
INCLUDING:CARBON MONOXIDE.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE AND LOCAL ENVIRONMENTAL CONTROL REGULATIONS.
EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF THROUGH AN
APPROVED WASTE MANAGEMEN T FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.